WHY UNDERSTANDING ESSENTIAL PLUMBING SKILLS IS CRUCIAL FOR INSTALLING A BATHTUB

Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub

Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub

Blog Article

Free Estimate

Here down the page yow will discover a lot of worthwhile information all about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


Tools You Need to Install a New Bathtub
Mounting a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the job can relocate immediately; if you need to open a wall to eliminate the old bathtub and also position the new bath tub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will require a helper to leave the old tub and also embeded in the new one. See to it you have qualified on your own for the work and fit attempting it. Instead of working with a specialist to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube connections.
This short article will help you install a new bathtub in your shower room if you have actually already gotten a new tub and do not require to alter the setup of your previous water pipelines.
Your tools and product list ought to comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the supply of water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is usually the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipes. Once the supply pipes have actually been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
    Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.

    Suitable New Touches


    If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the existing supply pipelines.
    If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next off, position the faucet in the placing opening in the bath/basin making certain that the washers are in area between the faucet and the sink. Protect the faucet in place with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The former type must be attached to the tap ends initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Installing the Bathtub


    Using the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are handy in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
    The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub until the spirit level checks out level.
    To mount taps, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
    Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as additionally examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
    Finally, fix the bathroom paneling as explained in the maker's instruction manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been used at least when as this will resolve it into its final placement.

    Getting ready for the Installation


    First of all, the sustaining framework provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
    Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall in between the bath and the tiling, causing issues with wetness and also possible leakages to the ceiling below.
    You can pick from a range of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealer can break rather early if you do not think about this motion before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or waterproof adhesive as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    Do you enjoy more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Give feedback below. We'd be pleased to see your ideas about this blog. Hoping that you come back again soon. Loved our content? Please share it. Help others check it out. I praise you for your time. Come back soon.


    Pro assistance? Dial.

    Report this page